DC – Thermopanel roof GL

Application: DC – The thermal panel is used as a roof construction in homes in areas with high wind draft, eg Greenland. The panel is finished with cement-based chipboard on the outside so that the roofing felt can be fixed mechanically.

Assembly: Built-in locking system that ensures a tight assembly that also contributes to stability.

Tried and tested: Over 10 years, the panel has been thoroughly tested in many different contexts and degrees of difficulty.

Vapor barrier: Vapor barrier is built into the panel.

Mould, fungus: The panel cannot contribute to mold and fungus formation

Insulation: The PU/PIR foam insulates 60% better than mineral wool, does not absorb water.

Fire: BS1Do, MK

Construction time: The roof of an ordinary detached house is erected in 1 day

Sustainability: Panels with PU/PIR foam could be reused even after many years, as the insulation remains intact.

Download as PDF2 MB
Panel type Core thickness U-value W/M2K Weight kg/m2 Fire
200 mm 172 0,13 49,3 Class 1 cladding
225 mm 197 0,11 50,3 Class 1 cladding
250 mm 222 0,1 51,3 Class 1 cladding
Production tolerances According to EN14509
Production measures Width: 1200mm Length: up to 8800mm
Fire approval Panel meets the requirement for class 1 cladding = K110, B-s1, d0 on both sides
Sound attenuation Contact DC-System for information
Tension table Contact DC-System or see it at www.dc-system.dk
Insulation PU/PIR foam
Surfaces The panels are supplied with 0.55 mm galvanized steel sheet on the outside and 12 mm cement chipboard between
and 12 mm cement chipboard and 0.55 mm galvanized steel sheet on the inner side
Assembling The panels are supplied with cast-in eccentric locks and rails over joint
Color White RAL 9010 or light gray 9002 colored steel plate inside and outside
Other things Need other information – contact DC-System. DC-System can, if desired, be helpful with measurement

Panels for housing and roof constructions

DC – The Thermo panel with locks is used as a roof structure in homes where there is a lot of draft, e.g. on Greenland. The panel has a super insulation that gives a very slim roof construction. There are no organics
materials in the panel, which eliminates the risk of mold and fungus in the panel. The panel contributes strongly to the green transition, as the CO2 contribution is very small / m2. The panel allows for a closed building on
very short time, so building moisture is minimized in other materials. The panel is particularly suitable for those roofs which must subsequently be finished with roofing felt.

The elements do not absorb moisture. When properly installed, they are considered airtight.

Sealant is applied to the edge of the panels, after which they are pushed together and locked by turning the locking key in the locking hole. The excess sealant is scraped away with the bottom of the silicone tube and the hole is closed with sealant.

Read about one of our other panels

DC-Mineral wool panel, Wall/Ceiling
Application: Office and industrial buildings where there are high fire requirements. Assembly: Th...
See panel
DC-Renovation panel
Application: Environments where high demands are placed on hygiene, including the food industry a...
See panel
DC – PU/PIR insulation panel with fire class EI 30
Application: Environments where high demands are placed on hygiene, including the food industry a...
See panel
DC fiberglass – insulation panel with locking system
Application: Environments where extreme demands are placed on hygiene, where aggressive chemicals...
See panel

Want to know more?
Contact us today

If you have questions about our products, services or would like a visit, please feel free to contact us. 

Fill out the form or give us a call +45 98 62 42 00 

Contact us immediately!

DC-System Insulation A/S

Nordvestvej 8, 9600 Aars